BCNPW - HIGH TEMPERATURE WEAR RESISTANT PUTTY RESIN

  • MSDS: BCNPW
  • Manufacturer: DEVCON
  • Product Name: HIGH TEMPERATURE WEAR RESISTANT PUTTY RESIN
  • National Stock Number: 8030-00N006795
Product Identification

Product ID:HIGH TEMPERATURE WEAR RESISTANT PUTTY RESIN
MSDS Date:01/01/1987
FSC:8030
NIIN:00N006795
MSDS Number: BCNPW

Responsible Party
DEVCON

Emergency Phone: 617 777 1100

Cage: 16059

Contractor
DEVCON CORP
DANVERS, MA 01923-3753 US

Telephone: 1-508-777-1100

Cage: 16059

Ingredients

GRAPHITE (CAS# 7782-42-5) (TLV IS RESPIRABLE DUST)

RTECS: VV7780000

ACGIH TLV: 2.5 MG/CUM

Hazards

Effects of Overexposure:EYE IRRIT.PRLNG &/OR RPTD SKIN CONT POSS IRRIT
& SENSITIZATION.

First Aid

First Aid:EYES:FLUSH W/PLENTY OF CLEAR H*2O FOR @ LEAST 15 MIN.CALL DR.
SKIN:RMV W/WARM SOAPY H*2O. INHAL:RMV PERSON TO FRESH AIR.

Fire Fighting

Flash Point:400F, TOC
Extinguishing Media:CO*2/DRY CHEM,POLYMER FOAMS FOR LARGE FIRES.
Fire Fighting Procedures:AVOID BREATHING SMOKE.
Unusual Fire/Explosion Hazard:NONE

Accidental Release

Spill Release Procedures:PREVENT SKIN & EYE CONT. SCRAPE UP & DISPOSE
OF IN SUITABLE CNTNRS.USE ABSORBENT COMPOUND IF NECESSARY. WASH
SPILL AREA W/INDSTRIAL CLEANING AGENT.

Handling

Handling and Storage Precautions:USE W/ADEQUATE VENT.AVOID SKIN
CONT.PVNT EYE CONT.STORE IN COOL,DRY PLACE.HANDLE IAW HAZ
POTENTIALITIES OF CURING AGENT WHEN MIXED THEREWITH.
Other Precautions:WASH THOROUGHLY AFTER USING.

Exposure Controls

Respiratory Protection:NONE IN NORMAL USE UNLESS IN CONFINED AREA OR
W/OTHR MATL REQ PROT.
Ventilation:GOOD GENL VENT.LOCAL EXH RECOMND FOR PRLNG/FREQUENT USE.
Protective Gloves:RUB/DISPOSABLE
Eye Protection:SFTY GLASSES W/SIDE SHLDS
Supplemental Safety and Health
PRODUCT DISCONTINUED 1985.

Chemical Properties

Vapor Pres:0
Spec Gravity:2.1
Solubility in Water:NIL
Appearance and Odor:DARK GRAY PASTE,LOW ODOR.
Percent Volatiles by Volume:0

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS
Stability Condition to Avoid:OPEN FLAME/EXCESSIVE HEAT.
Hazardous Decomposition Products:OXIDES OF CARBON,ALDEHYDES,ACIDS
Conditions to Avoid Polymerization:HT GENERATED IF MIX W/EPOXY
HARDNER.CAUTION IF MIX LGE QUANT

Disposal

Waste Disposal Methods:DISPOSE OF IAW FEDERAL, STATE, & LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.